Cables

Copper Patch Cord

Features

  • Snagless, molded boots provide strain relief and prevent kinking as well as snagless cable mining.
  • All Cat5e cables tested to 350MHz; Cat6 cables tested to 250MHz.
  • All have 4-pair, 24 AWG construction with RJ-45 connectors.
  • Available in both straight or crossover pinning.

 

 

 

 

 

 

 

Specifications

Electrical Characteristics
• Conductor DC Resistance - 89Ω/km (maximum)
• Insulation Resistance - 100Ω/km (maximum)
• Dielectric Strength - 500MV/m
• Certification: TIA/EIA

Physical Characteristics
• Wiring Scheme - TSB 568B (AT&T 258A)
• Approvals - RoHS Compliant
• Package Type - Polybag

Conductor (Qty. 4 twisted pair)
• Conductor Type - 24AWG (7/0.20), Stranded Bare Copper
• Insulation - H-D PE
• Diameter - 0.95 ± 0.02mm
• Colors - Blue, Blue-White, Orange, Orange-White, Green, Green-White, Brown, Brown-White

Connector Type (Qty. 2)
• Connector Type - 8P8C (RJ45)
• Gender - Male
• Connector Material - Polycarbonate
• Contact Material - Copper Alloy, Gold Plating - 50µm
• Hood Material - Moulded PVC

Overall Cable
• Jacket - FR-PVC
• Minimum Average Thickness - 0.55mm
• Outer Diameter - 5.30 ± 0.15mm

Product Uses
• 1000 BASE-T; 100 BASE-T; 10 BASE-T (IEEE 802.3)
• 4/16 Mbps Token Ring (IEEE 802.5); 100 VG-AnyLAN
• 100 Mbps TP-PMD (ANSI X3T9.5); 55/155 Mbps ATM

 

Duplex Single Mode Patch Cord

Features

  • • Different type of terminations SC to ST, LC to FC, etc.
  • • ANSI/TIA/EIA-568.B.3 compliant
  • • 50/125µm, 62.5/125µm Multimode Riser
  • • 1.6mm, 2mm, and 3mm Simplex / Duplex
  • • IEEE 802.3u, IEC 60794, TIA/EIA-568.B.3 compliant
  • • Electric interference immune
  • • Fibers offers low insertion loss once joined to connector
  • • Telcordia GR-326 tested
  • • Lab connectorized, each jumpers includes a quality certificate to state measuring standards
 

Specifications

  • • Maximum Connector Loss: 0.50 dB
  • • Typical Connector Loss: 0.30 dB
  • • Typical Return Loss: -55 dB
  • • Buffer Material: PVC
  • • Buffer OD: 900 µm
  • • Jacket Material: PVC (OFNR riser-rated)
  • • Jacket OD: 1.8 mm
  • • Installation Tensile Load: 100 N (445 lbs)
  • • Long-Term Tensile Load: 50 N (222 lbs)
  • • Maximum Tensile Load: 100 N/cm
  • • Installation (Loaded) Minimum Bend Radius: 5.0cm (1.97in)
  • • Long-Term (Unloaded) Minimum Bend Radius: 3.0cm (1.2in)
  • • Crush Resistance: 750 N/cm
  • • Impact Resistance: 1,000 cycles
  • • Flex Resistance: 5,000 cycles
  • • Attenuation at 1550 nm: 0.25 dB/km
  • • Attenuation at 1310 nm: 0.35 dB/km
  • • Operating Temperature: -20°C to +70°C

MPO Cable

Features

  • • MPO / MTP connector interface patch cord
  • • Customizable fiber optic cable length
  • • Available in 12 and 24 core cable fiber types
  • • Uses multi-mode 50/125um, OM3 /OM4 Bend-insensitive fiber or single-mode (G652D, G657A1) Bend-insensitive fiber types with type 2mm diameter
  • • Comply with IEC 61754-7, Telcordia GR-1435-CORE
  • • RoHS 6 compliant(lead free)
  • • Supports applications such as 40G LAN, 100G LAN or OTU4 100Gbps

 

 

 

 

Specifications

  • • Cable type: 3.2 mm round LSZH jacketed cable
  • • Bandwidth fiber: Multimode OM3 XG lazer optimized ≥2000MHzxKm @850nm
  • • Single Mode OS2 ITU-T G.652d 9micron
  • • Connector-Type: High connectivity MPO
  • • Connector Interface: MPO interface requirements: IEC61754-4.20 and IEC61754-7
  • • Connector End face: MPO end face geometry requirements: EN50377-15-1
  • • Polishing Quality: Polished end-face quality: IEC61300-3-35
  • • Insertion Loss: ≤ 0.5dB OM3 / ≤ 0.6dB SM OS2
  • • Return Loss: ≥ 25dB OM3; ≥ 35dB

Duplex Multimode Patch Cord

Features

  • • Different type of terminations SC to ST, LC to FC, etc.
  • • ANSI/TIA/EIA-568.B.3 compliant
  • • 50/125µm, 62.5/125µm Multimode Riser
  • • 1.6mm, 2mm, and 3mm Simplex / Duplex
  • • IEEE 802.3u, IEC 60794, TIA/EIA-568.B.3 compliant
  • • Electric interference immune
  • • Fibers offers low insertion loss once joined to connector
  • • Telcordia GR-326 tested
  • • Lab connectorized, each jumpers includes a quality certificate to state measuring standards
 

Specifications

  • • SC Connector Dimensions: 10.6mm Height x 26mm Width x 58mm Depth (with installed duplex clip)
  • • Maximum Connector Loss: 0.50 dB
  • • Typical Connector Loss: 0.30 dB
  • • Typical Return Loss: -25 dB
  • • Buffer Material: PVC
  • • Buffer OD: 900 µm
  • • Jacket Material: PVC (OFNR riser-rated)
  • • Jacket OD: 2.8 mm
  • • Installation Tensile Load: 100 N (445 lbs)
  • • Long-Term Tensile Load: 50 N (222 lbs)
  • • Maximum Tensile Load: 100 N/cm
  • • Installation (Loaded) Minimum Bend Radius: 5.0cm (1.97in)
  • • Long-Term (Unloaded) Minimum Bend Radius: 3.0cm (1.2in)
  • • Crush Resistance: 750 N/cm
  • • Impact Resistance: 1,000 cycles
  • • Flex Resistance: 5,000 cycles
  • • Attenuation at 1300 nm: 1.0 dB/km
  • • Attenuation at 850 nm: 3.5 dB/km
  • • Operating Temperature: -20°C to +70°C

LC-HD High Density LC connector patch cord

Features

  • • LC-HD’s lever design utilizes a flexible “pull-tab” allowing for the connector to be disengaged easily from densely loaded panels without the need for special tools.
    • IEEE 802.3u, IEC 60794, TIA/EIA-568.B.3 compliant
    • 9/125μm Single Mode that offers a great wide broadband
    • Telcordia GR-326 and IEEE 802.3u/802.3x/802.3z/802.3j standards tested
    • 9/125μm Single Mode
    • 2mm, and 3mm Simplex

 
 
01 mp   02 mp   03 mp  

Easy to release trigger connector

The LC-HD’s lever design utilizes a
flexible “pull-tab” allowing for the
connector to be disengaged easily
from densely loaded panels without
the need for special tools.
“Pull-Tabs” are available in three
standard lengths and multiple
colors.

60% increase in density

The LC-HD connector can be removed
using a simple pull tab, it eliminates
the need for finger access to the LC
connectors latch mechanism, therefore
LC adapters can now be mounted much
closer than spacing required in the past.

Stackable adapters

The LC adapter spacing was
limited by the room required to reach
LC connectors with the human fingers or
with special tools. The overall height of
standard LC connectors also required a
small vertical space above and below the
LC adapters. The low profile Senko LCHD,
together with it’s pull tab allow the
LC adapter to be stacked with absolutely
no vertical space.

 

Ordering Information

ho i ada

Simplex Single Mode Patch Cord

Features

  • • The Single Mode Jumper construction is designed to support tough usage, high performance interconnections, easy installation, and saving time
  • • IEEE 802.3u, IEC 60794, TIA/EIA-568.B.3 compliant
  • • 9/125µm Single Mode that offers a great wide broadband
  • • Telcordia GR-326 and IEEE 802.3u/802.3x/802.3z/802.3j standards tested
  • • 9/125µm Single Mode Riser
  • • 1.6mm, 2mm, and 3mm Simplex / Duplex
  • • Fibers offers low insertion loss once joined to connector
  • • Different type of terminations SC to ST, LC to FC, etc.
 

Specifications

  • • Maximum Connector Loss: 0.50 dB
  • • Typical Connector Loss: 0.30 dB
  • • Typical Return Loss: -55 dB
  • • Buffer Material: PVC
  • • Buffer OD: 900 µm
  • • Jacket Material: PVC (OFNR riser-rated)
  • • Jacket OD: 1.8 mm
  • • Installation Tensile Load: 100 N (445 lbs)
  • • Long-Term Tensile Load: 50 N (222 lbs)
  • • Maximum Tensile Load: 100 N/cm
  • • Installation (Loaded) Minimum Bend Radius: 5.0cm (1.97in)
  • • Long-Term (Unloaded) Minimum Bend Radius: 3.0cm (1.2in)
  • • Crush Resistance: 750 N/cm
  • • Impact Resistance: 1,000 cycles
  • • Flex Resistance: 5,000 cycles
  • • Attenuation at 1550 nm: 0.25 dB/km
  • • Attenuation at 1310 nm: 0.35 dB/km
  • • Operating Temperature: -20°C to +70°C

Simplex Multimode Patch Cord

Features

  • • Different type of terminations SC to ST, LC to FC, etc.
  • • ANSI/TIA/EIA-568.B.3 compliant
  • • 50/125µm, 62.5/125µm Multimode Riser
  • • 1.6mm, 2mm, and 3mm Simplex / Duplex
  • • IEEE 802.3u, IEC 60794, TIA/EIA-568.B.3 compliant
  • • Electric interference immune
  • • Fibers offers low insertion loss once joined to connector
  • • Telcordia GR-326 tested
  • • Lab connectorized, each jumpers includes a quality certificate
  • • to state measuring standards
 

Specifications

  • • Maximum Connector Loss: 0.50 dB
  • • Typical Connector Loss: 0.30 dB
  • • Typical Return Loss: -55 dB
  • • Buffer Material: PVC
  • • Buffer OD: 900 µm
  • • Jacket Material: PVC (OFNR riser-rated)
  • • Jacket OD: 1.8 mm
  • • Installation Tensile Load: 100 N (445 lbs)
  • • Long-Term Tensile Load: 50 N (222 lbs)
  • • Maximum Tensile Load: 100 N/cm
  • • Installation (Loaded) Minimum Bend Radius: 5.0cm (1.97in)
  • • Long-Term (Unloaded) Minimum Bend Radius: 3.0cm (1.2in)
  • • Crush Resistance: 750 N/cm
  • • Impact Resistance: 1,000 cycles
  • • Flex Resistance: 5,000 cycles
  • • Attenuation at 1550 nm: 0.25 dB/km
  • • Attenuation at 1310 nm: 0.35 dB/km
  • • Operating Temperature: -20°C to +70°C

Armour Fiber Patchcord

Starview armour fiber patch cord retains all the features of standard jumpers, but it is much stronger. With stainless steel tube inside the outer jacket to protect the central unit of the cable, the starview armour fiber patch cord is ideal to use in harsh environment. It is flexible but extreme resistant, anti-rodent and able to bend without being broken.

Features


  • • Resist damage by improper twist
    • Resistance of pressure and rodent bite
    • Fibers offers low insertion loss once joined to connector
    • 1.6mm and 2mm Simplex / Duplex
    • Fibers offers low insertion loss once joined to connector
    • IEEE 802.3u, IEC 60794, TIA/EIA-568.B.3 compliant
    • 50/125µm Multi Mode, 62.5/125µm Single Mode, 3mm Simplex
    • Stainless steel tube inside the outer jacket
    • Additional durability and protection as well as light weight.
    • Different type of terminations SC to ST, LC to FC, etc.

 

Specifications

  • • Standards:Telcordia GR-326, IEEE 802.3u/802.3x/802.3z/802.3j, IEC 60794, TIA/EIA-568.B.3
    • Fiber Jacket
    • Color: Multimode: gray/orange Single mode: blue
    • Diameter:3mm ± 0.05mm
    • Thickness:0.80mm ± 0.80mm
    • Temperature:-20°C up to 85°C

    • Fiber optic
    • Core diameter
    • Fiber:9/125µm, 50/125µm, 62.5/125µm
    • Value: ± 0.70mm
    • Cladding diameter:125.0 ± 2.0µm
    • Core concentricity : <=1.5µm
    • Cladding concentricity :<=1.0%
    • Wavelength
    Multimode: 850 nm / 1300 nm
    Single mode: 1310 nm / 1150 nm
    • Maximum value:<=0.03 / <=0.02
    • Recommended Light source
    Multimode:LED o VCSEL
    Single mode:Laser

How to choose optical fiber patch cord?

 

The Optial Fiber Patch Cord is available for any kind of configurations you need.

ordering

Take me to choose a connector!

Transceiver-Overview!